Car Brake Parts 2pcs Brake Disc 410*36mm Drilled Slot Plating

brake structure
Disc brake discs (discs) are divided into solid discs (single discs) and air duct discs (double discs). The solid disc type is easier for us to understand. To put it bluntly, it is solid. Vented Disc, as the name suggests, has the function of ventilation. From the outside, it has many holes on the circumference leading to the center of the circle, called air ducts. The air convection at the air duct is used by the car to achieve the purpose of heat dissipation, which is much better than the solid heat dissipation effect. Most of the cars are front-drive, and the frequency meter of the front disc is worn more, so the front air duct disc and the rear solid disc (single disc) are used. Of course, there are also air duct discs at the front and rear, but the manufacturing cost is not too bad.
The first picture in this article is a perforated scribing disc. Its braking performance and heat dissipation have been improved to a certain extent, but it has a large wear on the brake pads. DIY modified brake disc, friendly reminder: 1. The material of the disc must be good enough, without too many defects that affect the strength, such as large pores, sand holes, and shrinkage porosity is not allowed. 2. The spacing and size distribution of the holes, etc., because one more hole is drilled, the strength of the place is slightly weaker. If the disk breaks, the consequences are unimaginable. 3. Symmetrical equalization. If the balance of the disc is seriously damaged, it will have a certain impact on the spindle during driving. 3. This is a hard project, please be cautious. Without professional guidance, it is best not to act recklessly.
Brake discs with punched lines, also known as "high-speed discs" or "modified discs", are generally assembled in high-performance vehicles, such as racing cars, sports cars or sports cars. With the rise of the modification wind in the domestic automobile industry in recent years, many riders do DIY by themselves, obtain punched and scribed brake discs from various channels, and then change them by themselves. The perforated and scribed brake disc is a double-edged sword. Its advantages and disadvantages coexist, but the wear of this type of brake disc will increase the wear of the brake pads, and the material and processing requirements of the brake disc are also relatively high. Many small companies pretend to be brands from European, Taiwanese, Japanese and other manufacturers to produce high imitation brake discs, which requires many players who like DIY to pay more attention.
The brake disc is a very important part in the braking system. A good brake disc brakes stably, without noise and vibration. Many DIY players do not have certain professional knowledge and do not replace the brake discs by themselves, because the original brake discs have been tested by many professional engineers and can fully withstand the braking force of their own cars. Sometimes after replacing the punched and marked brake disc, the braking effect is not necessarily better than the original ordinary disc. Therefore, as for the total parts and components related to safety, it is necessary for all riders to be cautious when modifying.
In addition, there is a disc that integrates HUB, ABS ring, assembly bolts, bearing skins, etc., generally called bearing disc, and is used for larger models such as trucks.
Drum brakes have a cast iron piece shaped like a tambourine, called a drum, which is fixed to the tire and rotates at the same speed. Disc brakes have the advantages of better reactivity and stability, better heat dissipation, and easy replacement. The cost of drum brakes is lower and the absolute braking force is higher, and they are more used in the rear wheels of small cars. However, its wear rate is high, so at the same time the overall cost is high.

Product parameter

reference picture

Guangzhou Yuanxing Industrial Co.Ltd was established in 2017 and is located in Room 302, building 5, No. 7, Laowu street, Dongping village, Yongping street, Baiyun District, Guangzhou ,China. The location is very excellent and the transportation is convenient. We have very rich industry experience and is a trusted supplier. The company has production equipment and skilled front-line employees. Our boss has been engaged in the transformation of automobile braking system since 2011, have about 10 years of experience in this industry. Since 2017, we have set up our own factory, which can provide you with the best price and the best quality products. We specialize in producing aluminum alloy center cap and bracket, which can be customized according to different car models. Meanwhile we also sell complete set brake kit included brake calipers/brake disc rotors/brake pads/brake hose/aluminum center cap and brackets. Our products have strict quality control from the procurement of raw materials to the sale of finished products. Our company purpose is customer first, trying our best to meet the needs of customers. Our company's products are sold worldwide. With excellent quality and reasonable value, quality service, to win the trust and praise of our customers . Warmly welcome to visit our company and factory. We sincerely welcome friends from all over the world to visit our company and cooperate with us on the basis of long-term mutual benefits. We are looking forward to receiving your enquiry soon.