Jekit Big Brake Kit 8 Pot Caliper 405mm Drilled Disc Bell Bracket

From a practical point of view, we should pay attention to matching when selecting calipers. Generally, 4-piston calipers are enough for high-performance street cars. In addition, it is worth noting that although the weight of the brake caliper is similar, the high-grade brake caliper made of light metal (such as AP Racing, Brembo, etc.) is more than twice as light as the cast iron product, and the brake system is a part of the unsprung weight, and the load has a direct impact on the vehicle's handling. In addition, the heat dissipation performance of high-grade brake caliper is very high, which is very helpful to control the temperature of the brake system.

From a practical point of view, we should pay attention to matching when selecting calipers. Generally, 4-piston calipers are enough for high-performance street cars. In addition, it is worth noting that although the weight of the brake caliper is similar, the high-grade brake caliper made of light metal (such as AP Racing, Brembo, etc.) is more than twice as light as the cast iron product, and the brake system is a part of the unsprung weight, and the load has a direct impact on the vehicle's handling. In addition, the heat dissipation performance of high-grade brake caliper is very high, which is very helpful to control the temperature of the brake system.

How to Install Front Brake Discs
Compare the new brake rotors to the old brake rotors to be sure both are the same design.
Remove the brake pads from the caliper and use a C-clamp or disc brake spreader to push the caliper piston back in its bore. While doing this, keep an eye on the master cylinder to ensure the fluid doesn’t get pushed out of the reservoir. If necessary, remove a small amount of fluid from the reservoir using a suction gun or fluid extractor. Do not remove all of the fluid from the master cylinder—that will allow air to enter the hydraulic system.

Install the new brake pads into the caliper or reinstall your old pads if you’re reusing them.

Install the new brake rotor on the wheel hub.
Reinstall the caliper mounting bracket (if so equipped). Use a torque wrench to tighten the mounting bracket bolts to the manufacturer’s specification.
Position the caliper over the rotor.

Use a torque wrench to tighten the caliper mounting bolts to the manufacturer’s specification.
Top off the master cylinder reservoir if you extracted fluid during step #2.
Reinstall the wheel/tire assembly on the lug nuts.
Using a ratchet and socket, tighten the lug nuts until they’re snug.
Safely remove the jack stands and lower the vehicle.

Use a torque wrench to tighten the lug nuts to the manufacturer’s specification.
Warning: Before driving the vehicle or taking the transmission out of park, pump the brakes several times to ensure they feel firm. Your car will have little to no braking ability until the brakes are pumped, allowing the caliper piston to return to its original position.
First, pump the brakes with the engine off. Then start the engine (transmission in park and the emergency brake set) and pump the brakes again.

DO NOT drive the car until the brakes feel solid..

Front Brake Disc Replacement Tips

It’s highly recommended to replace both your brake discs and brake pads at the same time. The brake discs should always be replaced as a pair, as well.

Product

reference picture

Guangzhou Yuanxing Industrial Co.Ltd was established in 2017 and is located in Room 302, building 5, No. 7, Laowu street, Dongping village, Yongping street, Baiyun District, Guangzhou ,China. The location is very excellent and the transportation is convenient. We have very rich industry experience and is a trusted supplier. The company has production equipment and skilled front-line employees. Our boss has been engaged in the transformation of automobile braking system since 2011, have about 10 years of experience in this industry. Since 2017, we have set up our own factory, which can provide you with the best price and the best quality products. We specialize in producing aluminum alloy center cap and bracket, which can be customized according to different car models. Meanwhile we also sell complete set brake kit included brake calipers/brake disc rotors/brake pads/brake hose/aluminum center cap and brackets. Our products have strict quality control from the procurement of raw materials to the sale of finished products. Our company purpose is customer first, trying our best to meet the needs of customers. Our company's products are sold worldwide. With excellent quality and reasonable value, quality service, to win the trust and praise of our customers . Warmly welcome to visit our company and factory. We sincerely welcome friends from all over the world to visit our company and cooperate with us on the basis of long-term mutual benefits. We are looking forward to receiving your enquiry soon.